Hello Ole,
I have no firewall on the computenodes and I have the internal interfaces on kadmin2, opa and eth, in the trusted zone of the firewall. It should allow everything through. I'm using RHEL 9.4. I built the rpm packages from source using the admin guide https://slurm.schedmd.com/quickstart_admin.html : https://slurm.schedmd.com/quickstart_admin.html
"Kadmin2" and "headnode" are the one and same. This system is on an air gapped network and I had to hand jam everything. Sorry for the confusion.
No luck stopping the firewall service. Still the same issue.
I'll continue to read the documentation that you have sent me and see if I missed anything.
Thanks,
Kent
-----Original Message----- From: Ole Holm Nielsen via slurm-users slurm-users@lists.schedmd.com Sent: Wednesday, November 27, 2024 8:47 AM To: slurm-users@lists.schedmd.com Subject: [slurm-users] Re: sinfo not listing any partitions
Hi Kent,
This problem could perhaps be due to your firewall setup. What is your OS, and did you install Slurm by RPM packages or what?
Does sinfo work on your SlurmctldHost=kadmin2? Is the "headnode" a different host? Try stopping the firewalld service.
You can see some advice on firewalls in the Wiki page https://wiki.fysik.dtu.dk/Niflheim_system/Slurm_configuration/#configure-fir... There is information about Slurm installation and configuration in the Wiki pages in https://wiki.fysik.dtu.dk/Niflheim_system/
IHTH, Ole
On 11/27/24 15:56, Kent L. Hanson via slurm-users wrote:
I am doing a new install of slurm 24.05.3 I have all the packages built and installed on headnode and compute node with the same munge.key, slurm.conf, and gres.conf file. I was able to run munge and unmunge commands to test munge successfully. Time is synced with chronyd. I can't seem to find any useful errors in the logs. For some reason when I run sinfo no nodes are listed. I just see the headers for each column. Has anyone seen this or know what a next step of troubleshooting would be? I'm new to this and not sure where to go from here. Thanks for any and all help!
The odd output I am seeing
[username@headnode ~] sinfo
PARTITION AVAIL TIMELIMIT NODES STATE NODELIST
*/(Nothing is output showing status of partition or nodes) /*
Slurm.conf
ClusterName=slurmkvasir
SlurmctldHost=kadmin2
MpiDefault=none
ProctrackType=proctrack/cgroup
PrologFlags=contain
ReturnToService=2
SlurmctldPidFile=/var/run/slurm/slurmctld.pid
SlurmctldPort=6817
SlurmPidFile=/var/run/slurm/slurmd.pid
SlurmdPort=6818
SlurmdSpoolDir=/var/spool/slurmd
SlurmUser=slurm
StateSaveLocation=/var/spool/slurmctld
TaskPlugin=task/cgroup
MinJobAge=600
SchedulerType=sched/backfill
SelectType=select/cons_tres
PriorityType=priority/multifactor
AccountingStorageHost=localhost
AccountingStoragePass=/var/run/munge/munge.socket.2
AccountingStorageType=accounting_storage/slurmdbd
AccountingStorageTRES=gres/gpu,cpu,node
JobCompType=jobcomp/none
JobAcctGatherFrequency=30
JobAcctGatherType=jobacct_gather/cgroup
SlurmctldDebug=info
SlurmctldLogFile=/var/log/slurm/slurmctld.log
SlurmdDebug=info
SlurmLogFile=/var/log/slurm/slurmd.log
nodeName=k[001-448]
PartitionName=default Nodes=k[001-448] Default=YES MaxTime=INFINITE State=up
Slurmctld.log
Error: Configured MailProg is invalid
Slurmctld version 24.05.3 started on cluster slurmkvasir
Accounting_storage/slurmdbd: clusteracct_storage_p_register_ctld: Regisetering slurmctld at port 8617
Error: read_slurm_conf: default partition not set.
Revovered state of 448 nodes
Down nodes: k[002-448]
Recovered information about 0 jobs
Revovered state of 0 reservations
Read_slurm_conf: backup_controller not specified
Select/cons_tres; select_p_reconfigure: select/cons_tres: reconfigure
Running as primary controller
Slurmd.log
Error: Node configuration differs from hardware: CPUS=1:40(hw) Boards=1:1(hw) SocketsPerBoard=1:2(hw) CoresPerSocket=1:20(hw) ThreadsPerCore:1:1(hw)
CPU frequency setting not configured for this node
Slurmd version 24.05.3started
Slurmd started on Wed, 27 Nov 2024 06:51:03 -0700
CPUS=1 Boards=1 Cores=1 Threads=1 Memory=192030 TmpDisk=95201 uptime 166740 CPUSpecList=(null) FeaturesAvail=(null) FeaturesActive=(null)
Error: _/forward/_thread: failed to k019 (10.142.0.119:6818): Connection timed out
*/(Above line repeated 20 or so times for different nodes.)/*
-- slurm-users mailing list -- slurm-users@lists.schedmd.com To unsubscribe send an email to slurm-users-leave@lists.schedmd.com